Electrical and Earthing Accessories

Glazing bar hold fast, so it is used for attaching DC clips etc. on to a narrow projection such as angle iron.

We are manufacturer of brass plug pin, according to customers requirement and specifications.

Brass sheet metal part is used in wide range of applications like Fastening, riveting, Supports, Fitting, Locking and for various type of uses in electromechanical and Automobile Industries. It comprises with aother components types like Lugs,Washers, Tags, Links, Gaskets, Terminals, Banana Plugs, Tapping Clips and Hinges etc. All other brass sheet metal componentscan be manufactured as per customers designs and specification.

Air Terminals tape base, can be manufactured from gunmetal, brass or bronze. It is Used for vertical support to lightening conductor, mounting air terminal on the roof or flat surface. It is used for fixing of air rod and connecting tape.

C-Crimp Connector are manufactured of extruded electrolyte copper with thick walls, used for parallel and tap connections of copper cable. Appropriate tools should be use for installation of C-Crimp connectors.

Copper bonded earth rod installers the best economical methods to achieve lower earth resistances. Each rods are having a higher tensile strength and lower carbon steel core. With 99.95% pure copper, It is directly applied electrolytical and form a metallurgic bond with steel core and copper.

CD Tape Clip can be manufactured from gunmetal, bronze or brass. The clip with a hole at a base for fixing with building or structures with appropriate fasteners and well plugs.

These Plate IS used in concrete structure for convenient ground system connection points. They are used where reinforcing the bars are electrically continuous and to be used for down conductor. These earthing points allows easy access of the lightening protections & earthing systems. Grounding plate connection are result in current carrying capacity will be equal to that of the conductors or studs and cannot loosen or corrode.

Rod to "O" cable clamp are used to fix rod to cable conductor. These clamps are durable and resistant to corrosion. Clamps are made of brass or gun metal.

Plate type test clamp are used as T Joint or straight through joints of tapes. It is also used for testing points for the network by disconnecting the joints. These also used for heavy duty tape up to 50x6 tape.

Rod to Tape Coupling are made of copper alloy. Used with the air rod brackets to connect their rod and tapes.The coupling is screwed onto the air rod and then connects to the tape with the bolts.

Square tape clamp are made from brass or gunmetal. These are used for forming straight through cross and tee joint in network of tapes. The lids are secured by four screw.

Tower earth clamp are made of brass or gun metal. Tower earth clamp are designed for bonding copper conductor to metal surfaces.

Line tap are made from extruded brass and give high strength.It is available in brass natural and electroplated nickle plated from.

Sizes & Types:

Marine Type, Angle Type, Lucas Type and Strip Type battery terminals are basic types. Heavy or Medium and Small variant are of Angle and Strip types where Lucas type the sizes are 9.5mm, 11mm and 13mm. Marine Type is manufactured as per custom design and specification which comes with Stud and Wing Nut. However, any specific type and sizes can be manufactured as per customers design.

 

Type:

• Hex head bolt type battery terminal
• Solder less screw type battery terminals
• Post type battery terminals
• Angle bosh type battery terminal
• USA CAR BATTERY TERMINALS
• Sevier crimp type battery terminal
• Solder crimp type battery terminal
• Easy fix type terminal
• Knock out type terminal

Panel Board Accessories mainly comprise of angles, flats,cold rolled steel sheets,fittings, copper bus bars, door hinges, fuse contact & terminal, tubes/pipes,nuts and bolts, handle studs and other electrical instruments. Control panel are used for regulating function of electrical equipments. Electrical panel is Fitted with every necessary relay are also mean to protect electrical equipments from being damaged from short circuits and over-loadings.

Air Terminal conductors base is manufactured from gunmetal or bronze and can be used for supporting & connecting rod to the circular conductors of flat surfaces.

These Circular Conductor Clips are manufactured from copper base alloy. This clip has a hole at the base for fixing the building or structure with appropriate fasteners and wall plug

CD Tape Clip can be manufactured from gunmetal, bronze or brass. The clip with a hole at a base for fixing with building or structures with appropriate fasteners and well plugs.

Multi point mostly used with taper pointed air rod. Multi point installed at highest area of structure or building. Multi point are mostly made of copper. Also available in brass & gunmetal or bronze. Multi point also connect taper pointed air rod with elevation rod.

These clamps are used for straight connection of tapes. Being joints,it can also used as testing points for the network by disconnecting the joints.

Parallel groove connector is used for connecting or branching overhead conductors.Extruded create a high strength clamp.slotted holes allow adjusting for varying conductors on each side. its type test is accordance with IEC61238-1.Shape Body made from extruded copper or brass and bolt and spring wwasher are made of steel with hot dip galvanized plating.

Re-bar clamp are used for bonding to handrails,re-inforcing bars,pipes, etc.

Ridge saddle are made of gun metal or brass. Used for vertical support to lightening conductor air terminal on the roof edges.These are used for fixing air rod and connecting to tape.

Rod brackets are made of copper alloy. Rod bracket being used for providing projection from building or face.Rod bracket is mainly used with rod to tape coupling where it is not possible to fit saddle on the roof and theair rod has to be fitted on the side of the building.

These clamps are made from copper alloys.These clamp provide easy access to copper tape or conductor for inspection or testing.

Use with threaded and unthreaded rods, suitable for connecting earth rod with cable lugs

These are made from gunmetal or brass.These clamp are used for crossing over tapes and cable. To make straight through joint or T connection in a continues network.The lids are secured by four screw.

Square conductor clamp are made from gunmetal or brass these are used for 4 way connection straight or T joints for round conductors.The lids are secured by four screw.

We Manufacture Copper or Bronze Bolted Lug as per Customers Specifications (Drawing and Samples).

 

Features:

Bolted Copper Alloy Lugs are a quickest & easiest way of making a connection on the normal and Flexible conductors. Palms are machined top to Bottom for bolting on either surface. They can be used multiple times. Barrels have internal corrugations in the clamp to assist with current transfers.

Test clamp are suitable for end to end joint