Valve and Manifolds

Features:

• Screwed female ends.
• Full bore and Two-piece designs.
• Quarter turn and Lever operated.
• Any Thread as per customers requirement.

Brass manifolds are manufactured from forged brass and it is designed for distributing and recycle the water, heating system and floor heating.

Application:

• It is used in Fluid controlled systems for building and plumbing of oil, Water and non-corrosive liquid

Features:

• Screwed female end
• Forged Brass Body

Dimensions: (All Dimension are in mm)

Salient Features:

• Screwed Female ends
• Permits flow in one direction & shuts
  automatically if the flow reverses
• Forged Brass Body

 Dimensions:- (All Dimension are in mm)   Size Range from: - ½” (15 mm) to 2″ (50 mm) BRASS CHECK VALVE (VERTICAL)Features: -

• Screwed Female ends
• Single piece design
• Used for vertical lines only
• Permits flow in one direction and
  shuts automatically if the flow reverses
• Spring inside

   

Brass Angle Valve is manufactured from forged brass and it is chrome-plated and design for lower pressures and smaller pipeline like plumbing, heating systems and sanitary application.
Applications:

• It is used in Fluid controlled systems for building and plumbing of oil, Water and non-corrosive liquid.

Brass float valve is made of forged brass, designed to close when the fluid goes up up to fixed level, the floating ball is floating and controls the open and close the valve, widely used for plumbing, bathroom, tanks, and pipelines.

Application:

• It is used in Fluid controlled systems for building and plumbing of oil, Water and non-corrosive liquid

Needle valves create is used for controlling a flow of liquid and gas through the valve mechanisms. To easy adjust of the flow rates to any specified amounts desired, making a valve useful at a numbers of application. By controlling the needle valve rate, stress on the delivery system is kept to a minimum.

Markets:

• Industrial
• Pneumatic
• MRO
• Packaging
• Water

Features/Benefits:

• Accurate flow control
• Corrosion resistance
• Forged brass for improved long-term mechanical strength
• Metal-to-metal seal for positive sealing
• Low temperature seal for improved performance

 

Features:

• Screwed male end
• Two piece design
• Easy to Install
• Forged Brass Body
• BSP Thread

Dimensions: (All Dimension are in mm)

Features:

• Screwed female ends to BSP.
• Knob operated.
• Easy to Install.
• Forged Brass Body and Brass Nozzle

Dimensions: (All Dimension are in mm)

Swati Enterprise offer a variety of 2 way, 3 way and 5 way manifold valve. The 2 way manifold valve are designe for static pressures and liquid levels application; the 3 ways and 5 ways manifold valve are design for differential in pressure applications.
Features:

• Conveniently good for method of bleeding, blocking and pressure calibrating instrument.
• Design for connected systemsimpulse in line and transmitters.
• Combining the functions of tee, isolationvalve, calibration valve, all tube & fitting in a single valve configurations.
• Free swivel ball at end stemassure bubble tighten valve & closure without seat galling.
• Specially hardened ball seats is much ideal for both gas & liquid service.
• All stem packings are located below the stem thread prevent galling of corrosions and contamination.
• Adjustable packings reduce the risk of body leak.
• Fully back sealed bonnet prevent accidentals stem removal & blowouts.

Applications:

• for General plants service
• Pressure instrumentations devices
• Differential pressures instrument devices
• Pressure equalization
• Block & bleed application.

Dimensions: (All Dimension are in mm)

Swati Enterprise offers a Wide range of multi-station manifold. Can be customized according to the requirement of customers.

Applications:

• General plant services
• Pressure instrumentation devices.
• Differential pressure instrument device.
• Pressure equalization.
• Block & bleed application.